Call us Today +1 (805) 465 7677
Monday- Friday 09:00 am-05:30 pm PST
Cart0
  • No products in the cart.
Login

Register - Lost your password?

Does the ChipWerke harm my engine?

No, as our ChipWerke gives you only the performance reserved by the manufacturers which they provided in their engine design.
As the ChipWerke will only be switched on when you really need the power (e.g. when you accelerate, ChipWerke will not function during idling/traffic jams), the components like the engine, the clutch, the transmission and the brakes are only stressed in line with the technically feasible scope. All protection functions of the engine, like e.g. the emergency programs aren’t switched off. An engine tuning should only be made – no matter which kind of tuning – when a regularmaintenance e.g. oil & filter change, toothed belt, etc. is carried out.

Which is the lowest and highest mileage I can use the ChipWerke with?

You can use the ChipWerke regardless of the mileage of your vehicle. Due to the digital protection technology of your original ECU, you take no risk. Lots of car dealers install the ChipWerke in new cars even from the first kilometer. However, you should observe the run-in period recommended by the manufacturer. We also have customers who installed the ChipWerke at a mileage of more than 200,000 km. That’s no problem due to our digital technology; as long as the vehicle or engine is well maintained!

Can I use the ChipWerke again when I change my vehicle?

Yes, if your new vehicle has got the same injection system as your former one, then you could directly transfer over. However, it’s also possible that you need a new cable harness or new software. You can buy the cable harness you need from us and we are able to reprogram the ChipWerke for your new vehicle, with a small fee. For further inquiries regarding compatibility please contact us: info@chipwerke.com

Does ChipWerke Detectable by Service?

No is not detectable at all . After the removal of the ChipWerke it is not traceable and the vehicle is directly returned to its original performance. No hardware or software changes were made. Even if related memories were logged in the ECU, the responsibility to prove it falls on the manufacturers, because a faulty sensor would also give the same logged memory.
Thus the ChipWerke is ideal for leasing, financing or company vehicles. We have optimized the complete vehicle fleet of some of our major clients. As the operation is not traceable after the removal leaves no foot print, this is a decisive advantage; of course, your factory warranty remains.

In spite of the power improvement can I save more fuel? How does it work?

Experience shows that a fuel saving between 0.2 and 1.0l is possible after the installation of the ChipWerke . Due to the significantly increased torque in the lower RPM range it’s possible to upshift to the next gear early. This results in the mentioned fuel saving. However, this depends greatly on your driving behaviour, as well as serial tolerances and the motor characteristics of the vehicle. A lot of satisfied customers reported a reduction of consumption of up to 1.0l per 100 km or  up to 15% More MPG

How can I modify the performance on the ChipWerke ?

We deliver the ChipWerke with a basic setting appropriate for your vehicle. With this basic setting you achieve a power improvement of approximately 18-35 %. This is the perfect compromise between fuel saving and power improvement. There is no firm setting value for the maximum setting as the power input can vary from vehicle to vehicle, although the engines are the same. Refer to the installation manual for the fine tuning guide.For furter request please contact with us

Why does my vehicle computer show error messages(CEL) & why does my vehicle switch to the emergency program (limp mode)?

Due to manufacturer-determined serial tolerances, the power output of ChipWerke might be too high. However, you can correct it by yourself easily and in only a few steps by means of adjusting the rotary control switch.

Donec ac augue ullamcorper nisl sodales lacinia vel ac nunc ?

Ut tempus erat eu quam mattis, a vehicula sem luctus. Aliquam eu ipsum condimentum, elementum nisl eget, varius dui. Morbi ac mi ut odio blandit venenatis a nec justo. Cras lacinia sapien non sagittis pellentesque. Morbi eu pellentesque lacus, et suscipit lorem. In luctus lacus at velit imperdiet volutpat. Aliquam.

More Question ? Ask us!

Please do not hesitated to contact with us our technical and sale department will answer  all your questions? Contact Us